Front End Audio has teamed up with RME to offer some fantastic deals on select factory direct B-Stock products! This RME QuadMic II was deemed as "B-Stock" by RME quality control. In the nature of being B-Stock, do expect a minor cosmetic issue but rest assured that it has absolutely no impact on the functionality or performance of this unit. Otherwise, this unit is brand new, comes with everything as if it were brand new AND carries a 1-year manufacturers warranty. This is a rare opportunity to save 25% and grab a "just like new" QuadMic II from RME! Stock is limited to quantity on hand and will sell out quickly!
The RME QuadMic II Microphone Preamp is designed to deliver pristine and clear signal quality for demanding studio recordings. An excellent signal to noise ratio, lowest harmonic distortions and wide gain range make the QuadMic II your first choice for studio use! The RME QuadMic II Microphone Preamp is a 4-Channel unique mic preamp that allows to connect any kind of microphone to any line level input. It is battery powerable and thus excellent for remote applications. Each of the 4 channels features balanced microphone and line inputs with Neutrik XLR/TRS combo jacks, switchable 48V phantom power, phase reversal and a low cut filter. All channels are also equipped with LEDs for signal presence, clip state, and activated phantom power. The input amplification can be set from 6 to 60 dB. The balanced line level output signals are provided on the rear of the unit as four 6.3 mm (1/4") TRS jacks. A maximum balanced and unbalanced output level of +21 dBu makes the RME QuadMic II fully compatible to RME's converters and interface series having analog inputs.
The RME QuadMic II complements any RME system with line inputs by adding external microphone inputs. Since the unit runs on supply voltages from 9 to 18V DC, it can operate on virtually any power source available, including batteries and rechargeable batteries.
RME QuadMic II Microphone Preamp Connectivity
- 4 x Mic Preamp Inputs
- XLR/TRS Combo Input
- 4 x Line Outputs
- Phantom power per channel
- Low Cut per channel
- Phase reversal per channel
- DC powered, battery compatible
- Low power / wide range DC operation
RME QuadMic II Microphone Preamp Features
- 4 Separate microphone inputs with That hi-end mic preamp
- Phantom power 48V, low cut and phase switchable per channel
- 48V, Clip and Signal LED per channel
- Gain XLR in: +6 dB up to +60 dB
- Gain TRS in: +0 dB up to +54 dB
- Phantom power free TRS input
- Servo balanced inputs and outputs
- Wide frequency response with special RF input filters
- Wide operating voltage range
- 100% hum-free via internal switching regulators
- Lockable power connector
- Rack mount compatible (RM19)
RME QuadMic II Microphone Preamp Specifications
- Inputs: XLR or 1/4" TRS (stereo) jack, electronically balanced
- Input Impedance: XLR 2 kOhm, TRS 4 kOhm
- Signal to Noise Ratio (SNR): 129 dB EIN @150 Ohm
- THD: < 0.0005 % @ 30 dB Gain
- Crosstalk: > 110 dB
- Wide Frequency Response: With special RF input filter
- Frequency Response –0.5 dB: 5 Hz - 200 kHz
- Hi-Pass Filter: At 80 Hz, 18 dB/oct
- Line Out: 1/4" TRS (stereo) jack, servo balanced
- Maximum Output Level: +21 dBu
- Output Impedance: 75 Ohm
- Power Supply: Operates with voltages ranging from 9-18V DC
- High-Quality Switching Power Supply: For worldwide operation at 100-240 Volt
RME QuadMic II Microphone Preamp Includes
- RME QuadMic II 4-Channel Microphone Preamp
- Power Supply
- Power Cords
- 1 Year Warranty
No review yet, Be first to Write a Review