DPA ST4011A Stereo Microphone Kit

(No reviews yet) Write a Review
Product Code: 9999-13778
DPA ST4011A
$3,659.95
Availability: Usually Ships in 24 Hours

DPA ST4011A Stereo Microphone Kit

DPA ST4011A Stereo Microphone Kit

DPA ST4011A Stereo Microphone Kit Details
4011A cardioids are exceptionally linear in their frequency response â" also off axis, giving you the natural experience. They handle extremely high SPL and will therefore allow for close placement and are often used for piano recordings with a placement closer to the hammers or as overheads for drums.

The DPA ST4011A is a complete DPA 4011A Stereo Pair with two carefully factory-matched first order cardioid microphones. Even though the standard tolerances on DPA Reference Standards are extremely low, a stereo match is even closer.

The specially selected DPA 4011A microphones are matched within ±1 dB on both frequency response and sensitivity.

The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone/accessory inlay.

DPA ST4011A Stereo Microphone Kit Features
  • World-wide cardioid reference mic
  • Handles very high sound pressure levels
  • Carefully matched within ±1 dB
  • PeliTM Case transportation and protection
DPA ST4011A Stereo Microphone Kit Includes
  • Two carefully matched 4011A cardioid microphones
  • sturdy PeliTM case
  • holders
  • windscreens

DPA 4011A Cardioid Microphone Specifications

  • Directional characteristics: Cardioid
  • Principle of operation: Pressure gradient
  • Cartridge type: Pre-polarized condenser
  • Frequency range: 20 Hz to 20 kHz
  • Frequency range, ±2 dB: 40 Hz to 20 kHz
  • Sensitivity, nominal ±2 dB at 1 kHz: 10 mV/Pa; -40 dB re. 1 V/Pa
  • Equivalent noise level, A-weighted, re. 20 µPa: Typ. 18 dB(A) re. 20 µPa (max. 20 dB)
  • Equivalent noise level, ITU-R BS.468-4: Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting)
  • S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 76 dB(A)
  • Total Harmonic Distortion (THD): < 1 % up to 139 dB SPL peak
  • Minimum load impedance: 2 kohm
  • Dynamic range: Typ. 121 dB
  • Max. SPL, peak before clipping: 159 dB
  • Switchable attenuator: 0 dB / -20 dB
  • Output impedance: < 200 ohm
  • Cable drive capability: 100 m (328 ft)
  • Output balance principle: Impedance balancing with Active Drive
  • Common Mode Rejection Ratio (CMRR): > 60 dB
  • Power supply (for full specifications): 48 V Phantom power (± 4 V)
  • Current consumption: 2.8 mA
  • Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
  • Color: Matte black
  • Weight: 158 g (5.6 oz)
  • Microphone diameter: 19 mm (0.75 in)
  • Capsule diameter: 19 mm (0.75 in)
  • Length: 170 mm (6.7 in)
  • Output voltage, RMS: > 5 V
  • Polarity: +V at Pin 2 for positive sound pressure
  • Temperature range: -40 °C to 45 °C (14 °F to 113 °F)
  • Relative Humidity (RH): Up to 90 %
  • Matching tolerance: ± 1 dB
  • Phase deviation for kit: < 10°

No review yet, Be first to Write a Review