Home > Rack Gear > Preamps > Multi-Channel >

  Rupert Neve 5024 Portico Quad Mic Preamp

Rupert Neve 5024
Rupert Neve 5024
 
List Price: $3,295.00
Our Price: $2,945.00


Availability: Usually Ships in 3 to 5 Days
Product Code: 9999-08773

 

Rupert Neve 5024 Portico Quad Mic Preamp

Rupert Neve Portico 5024 Quad Mic Amp

Rupert Neve Portico 5024 Quad Mic Preamp Details

The Rupert Neve Designs Portico 5024 Quad Mic Preamp incorporates four channels of renowned preamplification, independent silk controls, two channels of DI inputs, and an M-S Decoder into a 1U enclosure. As a result, the 5024 is a workhorse preamplifier solution equipped to enhance the front end performance of any digital or analogue recording system. Each channel of the Portico 5024 is based around the custom transformers and class-A circuitry found in the 5012.

In addition to 72 dB of gain, the 5024‚??s mic pres include individually selectable phase, mute, phantom power, a selectable frequency high pass filter, and the Silk circuit which yields the rich warmth and presence of the renowned classic designs. Channels 1 & 2 of the 5024 feature a high-Z input designed for instrument level sources. Channels 3 & 4 feature an M-S switch, which enables Mid-Side decoding without the use of multiple console channels.

Microphone Input

The microphone input is balanced but not floating, being a variant of an instrumentation amplifer using a ‚??Transformer-Like-Amplifier‚?Ě (T.L.A.) configuration with a toroidal Common Mode Rejection Low Pass Filter that excludes frequencies above 150 kHz. The T.L.A. is followed by an actual input transformer permitting a full +25 dBu input signal to be handled at unity gain without an input pad over the whole audio spectrum. This combines the advantages of both an ‚??Electronically Balanced‚?Ě and true transformer input. When the Phantom voltage is switched off, this input serves as a very high quality line input with an impedance of 10,000 ohms.

Low Noise, Low Distortion Operation

Much care was given in designing the 5012 to produce as little noise and non-harmonic distortion as possible. Carefully implemented signal paths and Class A operation are a large part of the 5012's sweet, whisper quiet performance. For more information, go to Mr. Rupert Neve‚??s Design Notes.

Why Transformers?

It is helpful to review some of the essentials of transformers where it will be seen that a design needs to be viewed as a whole, not simply from the point of view of a single component.

The fine subtleties of circuit design relating to sonic performance are gradually becoming more clearly understood. For example, research has shown conclusively that frequencies above 20 kHz affect the way in which humans perceive sound quality. But, long before scientific evidence emerged a substantial body of musicians and engineers knew that equipment with apparently the same technical measurements could sound very different.

Incredibly small amounts of musically dissonant odd harmonics have a disastrous effect on the sound quality. Extraneous noise or interference that finds its way into a signal path seriously impairs performance of the whole chain.

Many control rooms make use of outboard gear that is not well protected from external signals. Poor grounding of such equipment can be a serious problem. ‚??Electronically balanced‚?Ě circuits much used in modern equipment, can give very good measurements on the test bench but they do not provide adequate rejection of the stray fields found in every working environment.

Input and output circuits must be freed from ground dependence so that only the ‚??wanted‚?Ě signal enters and leaves the processing path. Transformers are the ideal solution. The sweet and silky sound of Rupert Neve's classic old favorite consoles was achieved with big transistors and large high quality transformers. Rupert Neve Designs Portico modules achieve similar quality today without the bulk or the cost.

In order that modules can work together as would be expected (i.e. in a proprietary console configuration) without producing hum, R.F. interference, or other interactions, the connecting interfaces, grounding, levels and impedances must receive careful attention. Each Portico module is a complete integral signal processor that delivers its specified performance independently. This is one of the reasons that Rupert Neve Designs use transformers.

Rupert Neve Portico 5024 Quad Mic Preamp Features

  • Silk: Much could be written about this feature, suffice to say, that it gives a subtle option to enhance sound quality in the direction of vintage modules. The Silk button reduces negative feedback and adjusts the frequency spectrum to provide a very sweet and musical performance. Try it and make your own judgment.
  • M-S: The M-S button engages Mid-Side decoding on channels 3 & 4. Channel 3 level controls the mid signal, and channel 4 level controls the side signal.
  • Instrument Inputs: Balanced or unbalanced Hi-Z input for instruments using the Mic Pre's gain circuitry.
  • Level Meter: -30 dBu to +22 dBu With reference to the output
  • Mute: Cuts of the output signal post metering and pre Buss Output. Be sure to mute the outputs before engaging phantom power.
  • High Pass Filter: The High pass filter is a valuable aid in any signal chain but particularly so in a microphone preamplifier. Signals below 30 or 90 Hz can be attenuated at 12dB / Octave, leaving the range above this unaffected. This gets rid of building rumble, air handling motor hum etc.
  • Phantom Power: Provides 48V phantom power to microphones
  • Phase Inverts: Flips the phase of an incoming source 180 degrees

Rupert Neve Portico 5024 Quad Mic Preamp Specifications

  • Frequency Response: Main Output, no load, ‚?"3 dB @ 2 Hz ‚?"3 dB @ 160 kHz
  • Noise: Measured at Main Output, unweighted, 22Hz-22kHz, Terminated 150 Ohms. With gain at unity better than ‚?"92 dBu With gain at 66 dB better than ‚?"56 dBu Equivalent Input Noise better than ‚?"123 dBu
  • Gain: Unity to +66dB in 6 dB steps, Trim continuously adjustable from ‚?"6dB to +6dB
    • Line Input: Trim continuously adjustable from ‚?"6dB to +6dB
    • Maximum Output Level: Maximum output from 20 Hz to 40 kHz is +25 dBu.
  • Phantom Power: 48 Volts DC +/- 1%
  • Total Harmonic Distortion and Noise:
    • @ 1kHz, +20 dBu output: Better than 0.002% As above, Silk Engaged: Better than 0.2% Second Harmonic @ 20Hz, +20 dBu out Better than 0.004% @ 20Hz, +20 dBu out Better than 0.020% IM Distortion: Better than 0.002%
    • Slew rate Better than 4 V/uS High Pass Filter: Frequency: Selectable either 30Hz or 90Hz Slope: 12 dB/Octave Bessel

Click here to view all Rupert Neve products


You may also need...
Rupert Neve 5100-PS P-1 Power Supply (Powers 2 Modules) Rupert Neve 5221-RM Horizontal Joining Kit (2 Modules in Single Space) Rupert Neve 5211-RM Half-Rack Joining Kit
Our Price: $69.00

Add
Our Price: $49.95

Add
Our Price: $69.95

Add
Rupert Neve 5100-PS Rupert Neve 5221-RM Rupert Neve 5211-RM

Average Customer Review 4 of 5 Total Reviews: 1

| Write a review!


  0 of 0 people found the following review helpful:
 
Neve Sound in a tight package. June 16, 2016
Reviewer: Stephen Lawson - theMicSite.com from Minneapolis, MN United States  
Admittedly, this was a bit of a splurge for our studio, however I am very happy with it. The sound is everything you would expect from a Neve unit, clear and punchy. There is PLENTY of gain for any type of source. The build quality is very good.

I dinged it 1 star because the layout of the knobs makes it difficult to see the selected buttons unless the unit is at eye level. Other than that... if one must splurge... this is a good place to do it.

Was this review helpful to you?