ART Zdirect Passive Direct Box


(No reviews yet) Write a Review
Product Code: 7590
Adding to cart… The item has been added
In Stock, Usually Ships In 24 Hours

This item is in stock and typically ships in 1 to 2 business days. If you have a deadline then please contact us before placing the order so we can meet your expectations.

Got Questions? Need Support?

888-228-4530 Contact Us!

The ART Zdirect Passive Direct Box is a high quality totally passive interface that lets you connect instrument, line, or speaker level signals to a mixer or other balanced input thru a high performance audio isolation transformer.

The ART Zdirect Passive Direct Box' high impedance single-ended 1/4? input is converted by the transformer into an isolated balanced low impedance signal source. The ART Zdirects audio transformer has an extremely flat and wide frequency response and can handle high signal levels while still maintaining an isolated balanced low impedance output. This gives the ART Zdirect a very clean and neutral sound with a wide variety of signal sources and over long signal runs in high noise environments.

The Input Attenuator switches allow for a wide range of signal levels and the Input Thru jack allows for tapping off of your signal chain. The Ground Lift switch lets you totally separate the input and output signal grounds, when appropriate, to isolate two systems, thereby reducing hum and ground-loop noise.

What further sets the ART Zdirect apart from other “DI” boxes are its extended features and versatility. The ART has added a switchable low pass Filter that cuts out all very high frequency interference. This Bessel filter on the output is placed out of the audio range and is primarily intended to reduce radio frequency interference before it gets into the main system. The filter is also very effective in reducing any digital computer noise artifacts when using the ART Zdirect as an interface between a computer based audio workstation and your monitors. The Phase Invert switch, while not normally included with your run of the mill D.I. box, has been added to allow you to switch signal polarity right at the source. This feature is especially handy when you are combining a direct tap with a microphone feed in the mix.

The compact black anodized all aluminum case and it’s passive design allow the ART Zdirect to provide years of trouble free service in Live Sound, Permanent/Fixed Install, D.J., and virtually any PA application. It’s full feature set, rugged construction, and high-end specifications make the ART Zdirect the obvious choice.

ART Zdirect Passive Direct Box Features

  • Fully passive, high performance transformer design (no battery required)
  • Converts 50k ohm inputs into 600 ohm balanced outputs
  • Switchable input attenuation (0, -20, -40 dB) Switchable low pass filter
  • Switchable phase invert
  • Switchable ground lift (fully isolates inputs from chassis and outputs)
  • XLR connectors for balanced outputs
  • Rugged extruded aluminum case

ART Zdirect Passive Direct Box Specifications

  • Frequency Response: 10Hz -50kHz, +/-.5dB @ +4dBu
  • Total Harmonic Distortion: .01% Typical @ 1kHz, +18dBu, <.05% @ 100Hz, +18dBu
  • Input Connections: ¼ – inch TRS unbalanced, 50k O
  • Output Connections: XLR male balanced, 600 O
  • Output Phase: Switchable, Normal/Invert
  • Ground Lift: Switchable, fully isolates inputs from chassis and output
  • Input Attenuation: Switchable, (0dB, -20dB, -40dB)
  • Filter Type / Response: Switchable, Low Pass, -3dB @30kHz
  • Dimensions: 1.75?H x 4.2?D x 3.5?W (44.5mm x 107mm x 89mm)
  • Weight: 0.75 lbs (0.35 kg)

ART Zdirect Passive Direct Box Includes

  • Zdirect Passive Direct Box
  • Owners Manual
  • 3 Year Warranty

No review yet, Be first to Write a Review