Home > Microphones > Condenser Microphones > Small Diaphragm >

  Audix ADX10-FL Flute Microphone

Audix ADX10-fl
Audix ADX10-fl
Alternative Views:

List Price: $225.00
Our Price: $199.00

Availability: Usually Ships in 24 Hours
Product Code: 6272

Select Version



Audix ADX10-FL Miniature Flute Microphone

Audix ADX10-fl Miniature Condenser Flute Microphone

Audix ADX10-FLP Miniature Condenser Flute Microphone Details

The Audix ADX10FL P Miniature Condenser Flute Microphone is characterized with a uniformly controlled cardioid polar pattern, helping to isolate the area or section being miked from other instruments or vocals on stage. With a smooth and accurate frequency range of 50 Hz - 18 kHz, the ADX10FL P is lightweight, low profile and will provide natural sound with exceptional transient response.

The ADX10FL P, specifically for use with a flute, includes a clip that attaches to the headstock of a flute, an 8?? cable terminating to a mini XLR-f connector and a phantom power adapter (APS 911). Other model versions are available as well, one of which is the ADX10 FL; for use with the Audix RAD360 wireless system which includes a flute clip, 3?? attached cable terminating to a mini-XLRf connector.

Manufactured to high standards and tight tolerances, the ADX10FL P features a modular threaded capsule, machined brass body with matte black finish, high quality shielded microphone cable and a variety of optional accessories.


The ADX10 FL is designed to plug directly into the bodypack of the RAD360 wireless system. To use the ADX10 FL as a wired mic, the model that includes the phantom power supply (ADX10 FLP) will be needed. The ADX10 FL and ADX10 FLP are low impedance microphones and should be plugged into a ??mic level? input on your console, mixer or recording device. The ADX10 FLP requires phantom power and will NOT operate without phantom power voltage (minimum of 9 - 48 Volts) which is available on most professional mic preamps and mixing devices. If phantom power is not available on your equipment, use the Audix APS 911, a supplied accessory with the ADX10 FLP model that allows for battery operation. Avoid plugging or unplugging the microphone from a PA system unless the channel is muted or the system volume is turned down. Failure to do so may result in a loud ??popping? noise which could seriously damage the speakers in the PA system.


With the ??crown? of the flute detached, simply place the ??O-ring? portion of the ADX10-FLP mic clip at the end of the ??head joint? and reattach the crown to the head joint.

The APS 911 phantom/battery power supply:

The mini-XLRf connector at the end of the ADX10-FL plugs directly into the mini-XLRm connector on the APS-911 power adapter. Next, plug a standard XLR-XLR microphone cable to complete the connection from the APS-911 to the mixing board. The APS 911 has the option to be used in phantom power mode or battery mode. If there is no phantom power available on the mixing console or equipment being used to amplify your signal,

use the battery mode to power up the mic. If further reduction of bass frequencies or plosives is FREQUENCY / POLARS: needed, the APS 911 is equipped with a base roll-off filter.

Audix ADX10-FLP Miniature Condenser Flute Microphone Supplied Accessories

  • Flute clip (MC FLUTE)
  • External foam windscreen (WS10)
  • Carrying pouch (P1)
  • Battery / Phantom power adapter with on off switch and bass roll-off. Includes belt clip. (APS 911)

Optional Accessories

  • WS10S - Snap to fit external windscreen
  • MC10L - Metal clip with tension fit wire loop
  • APS 910* - Phantom power adapter

Audix ADX10-FLP Miniature Condenser Flute Microphone Specifications

  • Transducer Type: Pre-Polarized Condenser
  • Frequency Response: 50 Hz - 18 kHz
  • Polar Pattern: Cardioid
  • Output Impedance: 250 Ohms balanced
  • Sensitivity: 4.5 mV / Pa @ 1k
  • Equivalent Noise Level: 25 dB (A weighted)
  • Signal to Noise Ratio: 69 dB
  • Power Requirements: 5 - 52 Volts phantom
  • Maximum SPL: ≥120 dB
  • Cable/Connector: Shielded 3-Foot Cable terminating to a miniature 3-pin Female XLR connector
  • Polarity: Positive pressure on diaphragm produces positive voltage on pin 2 relative to pin 3
  • Housing/Finish: Brass / Black E-Coat
  • Weight: 110 g / 4 ounces
  • Length: 25 mm / .98 inches

Audix ADX10-FLP Miniature Condenser Flute Microphone Downloads

Click here to view all Audix products